<code id="6cia4"></code>
        <code id="6cia4"><em id="6cia4"></em></code>
        <center id="6cia4"><small id="6cia4"><optgroup id="6cia4"></optgroup></small></center><code id="6cia4"><nobr id="6cia4"></nobr></code>
        <th id="6cia4"><option id="6cia4"></option></th>
        <code id="6cia4"><nobr id="6cia4"><sub id="6cia4"></sub></nobr></code><tr id="6cia4"><sup id="6cia4"></sup></tr>
        <center id="6cia4"></center><code id="6cia4"><em id="6cia4"></em></code>
        <strike id="6cia4"></strike>

        <strike id="6cia4"><video id="6cia4"></video></strike>

        Single layer spray sterilization pot

        pro description:




        In simple terms, a sterilizing pot is a closed, pressurized heater used to heat food sealed in a container and a variety of sterilizing pot systems can be used for sealed packaging of commercially sterile food in containers. The sterilization pot system has some of the same characteristics: the system is pressurized and transfers temperatures well above the boiling water temperature.

        The system USES a medium (called a heating medium or a sterilizing medium) as a means of transferring heat to the product. The medium used in the pot includes pure steam. Hot water (container completely immersed in water, water spray or water spray) and steam/air mixture. Some systems use overpressure during sterilization and cooling to maintain container integrity and balance against pressure in the tank. This is necessary because some packaging containers have a limited tolerance for internal pressure. Some examples of overpressure sterilizing containers are semi-rigid plastic containers with heat sealers or bimetallic joint tank ends, flexible bags, metal plates, cardboard containers, and glass bottles. At 250°F the pressure is approximately 15psig (pounds per square inch), and any pressure applied to the sterilizing pot above this value is called overpressure. Sterilization systems that provide overpressure, such as 25-30psig (lb/square inch), can be operated at higher temperatures. The operation of the equipment must be appropriate to ensure that containers are commercially sterile after being sterilized.


        The equipment is composed of pot body, pot cover, opening device, locking module, safety interlock device, track, sterilizing frame, steam nozzle and several pipe mouth, etc. Inflatable silicone temperature-resistant sealing ring is adopted for pot cover sealing, which ensures reliable sealing and long service life. It has the characteristics of large heating area, high thermal efficiency, uniform heating, short boiling time of liquid material, easy to control the heating temperature, etc. The sterilizing pot is mainly used in food industry, medicine and other fields.


        The horizontal sterilization pot of this form is used in general canneries for the sterilization of atmospheric boiling water. The device can realize backpressure sterilization by introducing compressed air. If cooling is to be carried out in the pot, a water pump shall be used to drive the spray pipe at the top of the pot (or a water circulation system shall be used). During sterilization, the pressure inside the can will exceed the pressure outside the can (in the pot) due to the rising temperature caused by heating. Therefore, in order to avoid pressurization inside the bottle and capping, the two ends of the tinplate can should be protruded, so backpressure must be applied, especially for canned meat that needs higher sterilization temperature. The use of backpressure sterilization, that is, the use of compressed air into the pot to increase pressure, prevent cans and jump cap, the operation of the situation is described as follows: because the compressed air is a bad heat conductor, steam itself has a certain pressure. Therefore, in the sterilization heating process, do not put compressed air, but only to reach the sterilization temperature in the heat preservation, open compressed air into the pot, so that the pot increased 0.5-0.8 atmosphere. After special sterilization, cooling cooling, stop the supply of steam, cooling water into the spray pipe. As the temperature in the pot drops, the steam condenses, and the pressure in the pot decreases using compressed air to compensate.

        Device parameter list



        inner diametermm6009001000100120012001200130013001300150015001500
        Total Lengthmm1800250025003000250030004000320042005200450055007500
        Total widthmm1200150016001600180018001800200020002000220022002200
        total heightmm1500180020002000200020002000210021002100220022002200
        cage sizemm800X350750X550750X6201000X620750X7201000X7201000X7201000X8001000X8001000X8001000X9001000X9001000X900
        number of layers9151717202020222222242424
        Up to the cage93034344040604466887296144
        maximum area㎡2.512.315.620.821.228.542.834.852.269.864.285.5128.5
        design temperature145℃
        test pressure0.43Mpa
        design pressure0.35Mpa

        Equipment details


        Company strength

        [Yirui workshop]


        [Yirui team capacity]


        [Yirui case]


        Choice Yirui

        1. Company was founded in 1999, focusing on machinery for 20 years.

        2. On-site factory directly docking customers, welcome to visit the factory.

        3. Company has the technical department, the engineering department, own has the research and development ability.

        4. Company real-time tracking equipment after-sales situation, service to customers.

        5. Equipment real material, prevent fraud.

        Contact us

        • Phone: 13819729099
        • Tel: 0577-85857000
        • Fax: 0577-85857000
        • Email: 620107085@QQ.COM
        • Address: No. 678A, Between 8th road and 9th Road, Binhai Development Zone, Wenzhou, Zhejiang, China
        Looked and looked
        online message 在線留言